Painting Services
Wall Putty and Skim Coating in Dubai Silicon Oasis & Academic City
The MELLS provides wall putty and skim coating in Dubai Silicon Oasis with its own directly employed team. Wall putty and skim coating level a rough, patched or textured wall with thin coats of filler, each sanded flat, so the paint that follows lies smooth under any light. A supervisor visits first, and the written quotation follows before any work begins.
- Quotation
- Written, after a visit
- Response
- 2 hours in Dubai
- Quality checks
- 14 on every job
- Service
- Gold rated
5.0 on GoogleFully insuredNo subcontractorsOpen 08:00 to 19:00, Monday to Saturday
Wall Putty and Skim Coating at a glance
| Service | Wall Putty and Skim Coating |
|---|---|
| Location | Dubai Silicon Oasis & Academic City |
| Property types | Villas and apartments |
| Quotation | In writing, after a site visit and before any work begins |
| Typical duration | Usually one to three days, confirmed with the quotation |
| Team | Crew directly employed by The MELLS, with a named supervisor |
| Quality check | Wet film thickness checked on every coat and an adhesion test at handover |
| If a check fails | It is put right free of charge within 48 hours |
| Response | Two hours in Dubai for urgent work, planned work within 48 hours |
| Hours | 08:00 to 19:00, Monday to Saturday |
| Booking | Book a site visit on this page, call +971 55 444 0084 or email contact@themells.ae |
What is included
Interior and exterior painting by our own painters, with surfaces properly prepared, furniture fully protected and wet film thickness checked on every coat. A good paint finish is mostly preparation. Dubai walls move with heat, hairline cracks open at ceiling joints, and coastal air and irrigation mark exterior walls within a few seasons. We repair and prime before we paint, apply the system named in your quotation and leave the home clean enough to move straight back into.
- Loose paint and hollow plaster removed back to sound material
- Wall primed so the putty bonds and dries evenly
- Two or three thin coats applied by wide steel blade
- Sanded under a raking light, dusted and sealed before paint
How we carry out wall putty and skim coating
Skimming is done in thin layers, never one thick one. The wall is scraped, washed and primed. A cement based or acrylic putty is then drawn across it with a wide steel blade, filling hollows and covering old patches. Each coat dries, usually for several hours, before it is sanded with a fine abrasive on a flat block or a dust extracted sander and the next is applied at right angles. After the final sanding the surface is dusted down and sealed with primer, as bare putty is very absorbent.
Putty applied too thick cracks as it shrinks, and putty over powdery or damp paint lets go in sheets and takes the finish with it. Interior grade filler used on a wall that gets wet, such as one next to a bathroom or an irrigated garden, softens and blisters. In humid months the drying time between coats stretches, and sanding too early clogs the paper and tears the surface. The site visit tests how well the existing coating is bonded, checks for moisture and establishes the level of flatness you expect.
How it works
The same method on every job, so the result does not depend on who is on shift.
- Survey, colour and written scope. We measure, test the existing coating and agree colours, sheen and the number of coats. The written quotation names the paint system and the scope.
- Protection. Furniture is moved and wrapped, floors are covered edge to edge, and switches, handles and light fittings are masked or removed.
- Surface preparation. Walls are washed, flaking paint is scraped back, cracks are opened and filled, and everything is sanded flat. Damp or salt affected areas are treated before any paint goes on.
- Primer and finish coats. A sealer or primer suited to the substrate is followed by two finish coats. Wet film thickness is checked on every coat.
- Snagging and handover. We inspect in daylight with you, touch up, clean down and hand over a paint schedule listing brand, colour codes and batch numbers for future touch ups.
Talk to a supervisor about wall putty and skim coating today.
Why choose The MELLS for wall putty and skim coating
What an ordinary job leaves out, and what you can hold us to.
| Point | An ordinary job | The MELLS |
|---|---|---|
| Quotation | A figure over the phone, with extras added on the day | A written quotation after a site visit, and nothing added on the day |
| Team | Crews supplied through agencies or subcontractors | Crew directly employed by The MELLS, with a named supervisor |
| Preparation | Paint rolled over cracks, dust and damp | Cracks filled, surfaces sanded and primed before the first coat |
| Handover | The job ends when the crew leaves | Wet film thickness checked on every coat and an adhesion test at handover |
| Aftercare | A return visit is charged | A failed check is put right free of charge within 48 hours |
Our commitments on every wall putty and skim coating job
The same standard on a single room or a whole estate.
Written quotation
The scope is fixed in writing before any work begins.
Named supervisor
One person is responsible for your job from the visit to handover.
Checked before handover
Wet film thickness checked on every coat and an adhesion test at handover.
Put right within 48 hours
If a check fails, we come back and correct it free of charge.
Fully insured
Our work in your home or premises is covered by insurance.
Discreet crews
Uniformed, briefed on your house rules and respectful of your privacy.
Wall Putty and Skim Coating in Dubai Silicon Oasis: what we plan for
Dubai Silicon Oasis is a free zone technology park with a full residential side. Cedre Villas and Semmer Villas are gated compounds of family villas. Around them stand mid and high rise apartment buildings such as Silicon Gates, Palace Towers, Axis Residence and Arabian Gate, and office addresses including IT Plaza and Dubai Digital Park. Dubai International Academic City next door is made up of university campuses and student housing, and Liwan and Majan are apartment districts in the same part of the city.
Sheikh Mohammed Bin Zayed Road and the Dubai Al Ain Road meet beside the community, so road facing glass and sills carry a traffic film. Open desert begins just beyond Academic City, and in Liwan and Majan empty plots stand between finished blocks. Sand reaches balconies and AC filters from both. A move out repaint is usually one colour throughout, and the skill is in the preparation. Plug holes are filled twice, because filler shrinks, then sanded and spot primed so the patches do not flash through the finish. Villa exteriors in the compounds follow the community colour, which is checked with the management before paint is ordered.
Cedre Villas and Semmer Villas have gatehouses, and the resident registers the crew in advance. Apartment and office buildings issue a contractor permit and a service lift slot on request, and The MELLS makes that request. Campus and free zone rules are confirmed at the site visit.
What your quotation depends on
A quotation for wall putty and skim coating in Dubai Silicon Oasis follows a site visit. The supervisor looks at the points listed here and you receive a written quotation with a defined scope before any work begins. Once you accept it, nothing is added on the day.
- Wall and ceiling area and ceiling height
- Condition of the surface and how much repair is needed
- Paint system, sheen and number of coats
- Colour changes, feature finishes and access equipment
Related Painting Services services in Dubai Silicon Oasis
Each one has its own scope and method.
Villa Painting
Apartment Painting
Interior Painting
Exterior Painting
Wall Painting
Antifungal Wall Painting
Facade Painting
Fence Painting
Move Out Painting
Office Painting
Ceiling Painting
Wall Crack and Plaster Repair
Feature Walls
Decorative and Textured Finishes
Wood and Door Painting
Kitchen Cabinet Painting
Boundary Wall Painting
Metal Gate and Railing Painting
Nursery and Kids Room Painting
Bedroom Painting
Living Room Painting
Bathroom Painting
Kitchen Painting
Majlis Painting
Staircase and Hallway Painting
Townhouse Painting
Penthouse Painting
Single Room Painting
Paint Touch up
Damp Wall Treatment
Venetian Plaster and Stucco
Limewash and Mineral Paint
Two Tone and Colour Block Walls
Paint Colour Consultation
Airless Spray Painting
Skirting and Trim Painting
Pergola and Timber Staining
Garage Floor Painting
Exterior Texture Coating
Paint Stripping and Removal
Shop and Showroom Painting
Restaurant and Cafe Painting
Warehouse Painting
Clinic Painting
School and Nursery Painting
Building Corridor and Lobby Painting
Car Park Line Marking
House Painting
Commercial Painting
Building Painting
Roof Painting
Paint Colour Matching
Water Damage Paint Repair
Hotel Painting
Salon and Spa Painting
Gym Painting
Mansion Painting
Studio Apartment Painting
Epoxy Flooring
Wall Putty and Skim Coating across Dubai Silicon Oasis
Questions about wall putty and skim coating in Dubai Silicon Oasis
What does wall putty and skim coating include?
Wall putty and skim coating level a rough, patched or textured wall with thin coats of filler, each sanded flat, so the paint that follows lies smooth under any light. The work includes loose paint and hollow plaster removed back to sound material; wall primed so the putty bonds and dries evenly; two or three thin coats applied by wide steel blade.
Is skim coating needed before every repaint?
Not at all. Sound walls with a few defects only need local filling. A full skim is worth doing when a wall has many old patches, a heavy roller texture, peeled areas or wallpaper damage, or when a darker colour or a sheen finish would expose every flaw.
How dusty is the sanding?
Sanding putty makes fine white dust, so the room is sealed with a zipped dust curtain, AC grilles are covered and a sander connected to a vacuum is used for the large areas. Hand sanding at corners still releases some, and the room is vacuumed before priming.
How much does wall putty and skim coating cost in Dubai Silicon Oasis?
We do not publish prices, because no two jobs are the same. The main factors: wall and ceiling area and ceiling height; condition of the surface and how much repair is needed. Book a site visit: a supervisor from The MELLS looks at the work and you receive a written quotation with a defined scope before anything begins.
Who provides wall putty and skim coating in Dubai Silicon Oasis?
The MELLS provides wall putty and skim coating in Dubai Silicon Oasis. The work is carried out by people The MELLS employs directly, under a named supervisor, 08:00 to 19:00, Monday to Saturday. To arrange it, book a site visit on this page or call +971 55 444 0084.
How long does wall putty and skim coating take?
Usually one to three days, confirmed with the quotation.
Which paint brands do you use?
We apply the paint system named in your quotation. Most clients choose premium washable emulsions from the major brands stocked in Dubai, and we are happy to work with paints specified by your designer.
How do you protect furniture and floors?
Furniture is moved to the centre of the room and wrapped. Floors are covered edge to edge, and fittings are masked or removed. The crew cleans down every day.
Do you repair cracks and damp patches before painting?
Yes. Cracks are opened, filled and sanded, and damp or salt affected plaster is treated and sealed first. Painting over a defect only hides it for a few months.
How do your crews get access to Dubai Silicon Oasis?
Cedre Villas and Semmer Villas have gatehouses, and the resident registers the crew in advance. Apartment and office buildings issue a contractor permit and a service lift slot on request, and The MELLS makes that request. Campus and free zone rules are confirmed at the site visit.
Do you cover Academic City, Liwan and Majan?
Yes. Student housing, campus buildings and the apartment blocks of Liwan and Majan are all covered. Tell us the building name when you call, because access rules differ from one landlord to the next.
How do I choose a company for wall putty and skim coating in Dubai Silicon Oasis?
Ask four things: who employs the people who will come, whether the scope is written down before work starts, how the result is checked, and what happens if something is missed. The MELLS uses its own staff, quotes in writing after a site visit, checks every job (wet film thickness checked on every coat and an adhesion test at handover) and puts right any failed check free of charge within 48 hours.
Can you come to Dubai Silicon Oasis at short notice?
Yes. Crews travel from our Barsha Heights base, and urgent work in Dubai is attended within two hours between 08:00 and 19:00, Monday to Saturday.
Page updated by The MELLS, Damac Executive Heights, Barsha Heights, Dubai.